5.0 Peak Horsepower - High performance wet/dry vacuum
Unique Design - Stores hose, accessories and 20' power cord inside the vac keeping everything organized and close at hand
Large Cushioned Handle - Portable and folds away for storage
Flat Top Work Surface - Increases your effective work area
Polypropylene Drum Construction - Rugged construction to meet the high demands of worksites
4.5 Gallon Drum - Cleans up of most spills & messes at work-sites and busy shops
1-7/8" Ultra-flexible Locking Hose - Won't pull loose during use; and the 2' compact hose extends to 7'
Blowing Capacity - Blow leaves from walkways or decks and debris from job sites, tools, etc
Qwik Lock® Filter 

Amps: 7A (120V)
Blow energy/torque: 1.8 ft.-lbs
No load speed: 0 to 1,500 RPM
No load blows per minute: 0 to 5,625 BPM
Thin wall bit capacity: 2-1/2″
Solid bit capacity: 1″

Draw from any fresh water source including lakes, pools and buckets - just drop in the 20' hose and start spraying

Snap-on’s new 7850 series of cordless tools feature a microprocessor controlled trigger switch which maximizes tool performance, runtime and durability.  The new CT7850 1/2" Drive Cordless Impact Wrench has a torque output of 450 ft./lbs. and is powered by an 18V lithium battery.  This versatile cordless impact provides more torque at a smaller size and lighter weight, giving the user more control with less strain. W/battery and charger

Missing 14mm

Powerful 12V motor cuts up to 2 -inch schedule-40 PVC in as little as 3 seconds



Ultra-sharp so it reduces the need to remove burrs and shavings



Quick-return blade helps to increase productivity when making repetitive cuts



Stainless-steel blade and aluminum jaw are impact, water and rust-resistant



Variable speed trigger gives a controlled cut in both cold and warm weather



On-board fuel gauge displays remaining battery charge and run time (battery not included)



Convenient offset blade: facilitates cutting of PVC in walls, close to walls or in the ground

Hilti DX460 Powder Actuated nail gun

Single Stage Pump
Cast Iron Cylinder with Rod Inserts
Air Regulator and Gauge Pre-Installed
Dual Control Valve Pre-Installed
Dual Voltage 110/220 motor (pre-wired 110v)
Deep finned Aftercooler for Moisture removal
Stainless steel reed valves
Low Profile 9 Gallon Tank Assembly

Hilti POL 10  Builder's level w/case

Schumacher SC1389 3 Bank 15A battery charger

Depth adjustment engineered for more precise flush and countersink finish
Quick release cam-lock opens nose assembly to clear jammed staples, minimizing downtime
Built-in air filter minimizes dust and debris from entering tool
Ideal for lathing, roofing and sheathing
Top-loading magazine allows operator to quickly load 16 gauge, 1" wide crown staples from 1" to 2" in length
Rugged aluminum magazine has large holding capacity (up to 140 staples)
Rubber bumpers protect the tool and surface from damage
Compact with less weight for all day use
Multi-directional exhaust port directs exhaust air away from operator
Rubberized handle for better fit and added comfort

 

Lightweight, break-through ergonomic design to reduce user stress and strain.

360 degree rotating nose enables operation from any position.

Front-access tension-adjustment wheel permits fast, easy changes.

Single handle operation for fast installation
Cable tie side entry for immediate positioning of tie and tool
Controlled tension, fully adjustable
Easy removal of excess tie
Automatically tensions and cuts off tie when predetermined tension is reached, providing more reliable and consistent installations*
Installs standard .18 in. (4.6mm), light-heavy .25 in. (6.4mm) and heavy .31 in. (7.9mm) cross section ties

7 The mainstay basic 360 prism, compatible with all Trimble instruments and GNSS receivers

The Trimble VX&S 360 Prism is a basic and low cost 360° prism compatible with the majority of total stations.

It is useful in short and mid-range applications.

The powerful 15-Amp saw delivers 4.0 max HP, with a large machined aluminum tabletop and a wide 25 In. ripping capacity. The Gravity-Rise Stand provides easy setup and take down. The SquareLock rip fence is engineered for trueness. The 4100 table saw also comes equipped with advanced electronics, such as soft start, constant response circuitry and overload protection.

Delta 28-161 ID: 73791 Table top band saw

Metabo HPT 12-Inch Sliding Compound Miter Saw, Double Bevel, Laser Marker, Compact Slide System, 15-Amp Motor, Large Sliding Fences

King Industrial 6" Jointer

3/4-inch to 1-3/4-inch coil roofing nailer with lockout mechanism prevents firing when empty
Adjustable depth control, full round driver, body and magazine wear guards, side-load canister
Durable yet lightweight magnesium housing and carbide tips for long life
Patented single-action side load canister for fast, one-step nail loading.

powerful and efficient brushless motor provides optimal cutting performance in a variety of materials
high maneuverability with its lightweight and compact design
quickly adjust the bevel capacity from 0 - 50° with the tool-free bevel lever
convenient storage on the jobsite with the built-in rafter hook
added safety: electric brake quickly stops the blade after the trigger is released


       . With 4AH battery and charger

12-Piece 6-Point 3/8" Drive Metric Socket Set
Opti-Torque™ applies torque to fastener sides, not corners which allows more torque to fastener and longer life
Counter-Torque™ distributes the torquing stress uniformly throughout the socket extending socket life

High-visibility laser markings help technicians identify sockets quickly
Opti-Torque system applies torque to the fastener sides, reducing corner round off
Counter-Torque distributes the torquing stress uniformly throughout the socket, extending socket life

Loosen and tighten any 6pt, 12pt, spline, TORX, square and even up to 50% rounded off fasteners
90 tooth head ratcheting wrench gains access where standard ratcheting wrenches will not fit with a minimal 4° swing arc
Reversing lever with 12° offset provides on-the-fly ratcheting adjustability with knuckle clearance

88 gear teeth produce a swing arc just over 4°, allowing faster work in the most compact spaces
Unique 9 position locking flex head ensures that the ratchet head maintains the desired position regardless of size or applied load
Slim profile allows better access in tight areas

Columbia Taping bazooka

Best in class 0.2 % accuracy
0.01 mA resolution and sensitivity
Measure 4 to 20 mA signals without ”breaking the loop”
Measure mA signals for PLC and control system analog I/O
Dual backlit display with both mA measurement and percent of 4 to 20 mA span
Measurement Spotlight illuminates hard to see wires in dark enclosures
Detachable clamp with extension cable for measurements in tight locations
Measure 10 to 50 mA signals in older control systems using the 99.9 mA range
Automatically change the 4 to 20 mA output for remote testing
Power saving features, auto-off, backlight timeout extend battery life
Hold function captures and displays changing measurements
Measure 4 to 20 mA signals with in-circuit measurement
Simultaneous mA in-circuit measurement with 24V loop power for powering and testing transmitters
Source 4 to 20 mA signals for testing control system I/O or I/Ps

Max. detection depth for object localization: 5-29/32 in
Accuracy of depth indication: ±3/8 in
Localization accuracy: ±5 mm

3000 reciprocating strokes per minute
Quick-action paper clamps
Solid rubber knob
Ergonomic grip

Matco Tools 3/8"  impact wrench with 5Ah battery and charger/case

Dewalt 1/2" Hammer Drill w/battery and charger

Made in Germany
Vial accuracy for life
Tough box beam construction
Extends from 7 to 12 feet
Hand holes for easy handling

Dewalt Laser Level

Ideal for undercutting baseboard, walls, door jambs, under toe-space and inside corners
The height of cut is adjustable from flush to 1" above the floor with 1/8" graduated scale for working with different floor coverings from sheet vinyl to thick ceramic tile and wood
The depth of cut is adjustable to suit a variety of material thicknesses from 0-1-1/4" with an adjustable fence
Large, flat base prevents tipping and assures accurate, level cutting

 CarpetPro Electric Stapler uses 20 Gauge 3/16" Crown staples from 3/8" to 9/16" in length

360° Rotating Handle locks at 45° increments
Powerful 13 amp motor delivers 0-3,000 SPM for high-performance orbital cutting in a variety of materials
1-1/4" stroke length provides maximum cutting speed
Variable speed trigger delivers smooth acceleration and performance to match speed to the application
Gear protecting clutch absorbs high impact forces caused by blade lock-ups to extend motor and gear life
Counter-Balance mechanism reduces vibration for smoother operation
Quik-Lok blade clamp system offers fast, tool-free changes

6.2 AMPS Corded

·    WiFi transmission, support iPhone, iPad, iPod Touch, Android smartphones and tablets
·    Support up to 150 Mbps via fast wi-fi wireless 
·    Video recording and photo capture capability
·    Waterproof 9mm camera with 100cm (3.3ft) flexible extended tube meet IP67 standard
·    Increased visibility with 3x zoom capability
·    Powered by 4x AA batteries with 3-4 hours continuous use
·    Flexible semi-rigid cable can be bent into many shapes to fit into unreachable areas
·    Include hook, mirror, and magnet for added flexibility
·    Lightweight, handheld design, flexible, and convenient to use
.    Extension cables ( 1M, 2M & 5M ) can be purchased separately.

• Power: 5.7 Amps, 110–120 VAC

• Water Removal: 80 Pints/Day @ AHAM (60% RH)

• Blower: 170 CFM

• Operating Range: 33°F to 110°F

Powerful .6 horsepower motor

3/4 Ton 10-Feet Lift Mini-Mite Ii Lever Chain Hoist-Super Heavy Duty

CC-DC Inverter Welding Power Source, Output: 120A, 25V, 95 Max OCV, 100% Duty Cycle, Input: 230V, 25A, 3.8 Kw, 1PH , plus cables

SDS-max bit system provides tool-free bit changes with automatic bit locking, dust protection and maximum impact energy transfer rate
Combination dual mode selector 2 modes of operation: rotary hammer and hammer only mode
Variable speed dial provides accurate bit starting and controlled chipping applications
Turbo Power feature delivers 10% more power in hammer only mode

Weld 7018-1 is a general - purpose basic DC + low Hydrogen stick welding (SMAW) electrode.  Excellent for general purpose welding.  Good impact values down to -45°C.  (121 pieces) 

21.6V Red Cut-out tool W/battery

ready to work

Reverse feature offers added versatility
Great for a variety of outdoor jobs, such as digging plant holes
Holds up to 1/2 in. drill shank

 Plunge Base with spare parts

No load speed: 3,200 RPM
AMPS (120V): 15.0 A